Understanding Concept of Striping, Mirroring & Parity

If you want to work as a Storage administrator or a SAN, NAS expert, then you should have good knowledge of some basic terms in storage and backup. Today we are going to talk about basic RAID levels, which you must understand.

As you must be knowing that RAID is the most widely used data protection technology that is used today and multiple disks work as part of a set to provide protection against HDD failures. Striping, Mirroring & Parity are the three basics of RAID levels, which we are going to discuss.

 

Understanding Concept of Striping, Mirroring & Parity

 

Striping, Mirroring & Parity

 

1. Striping:

For me, Striping is the most confusing RAID level as a beginner and needs a good understanding and explanation. We all know that RAID is a collection of multiple disk’s and in these disks, a predefined number of contiguously addressable disk blocks are defined which are called as strips and collection of such strips in aligned in multiple disks is called stripe.

 

RAID Striping

 

Suppose you have hard disk, which is a collection of multiple addressable blocks and these blocks are stacked together and called strip and you have multiple such hard disks, which are place parallel or serially. Then such a combination of disks is called stripe.

 

Note: Without mirroring and parity, Striped RAID cannot protect data but striping may significantly improve I/O performance.

 

 

2. Mirroring:

Mirroring is very simple to understand and one of the most reliable ways of data protection. In this technique, you just make a mirror copy of disk which you want to protect and in this way you have two copies of data. In time of failure, the controller uses a second disk to serve the data, thus making data availability continuous.

 

RAID Mirroring

 

When the failed disk is replaced with a new disk, the controller copies the data from the surviving disk of the mirrored pair. Data is simultaneously recorded on both the disk. Though this type of RAID gives you the highest availability of data, but it is costly as it requires double the amount of disk space and thus increases the cost.

 

Recommended Article: Difference between RAID 10 & RAID 01

 

3. Parity:

As explained above, mirroring involves high cost, so to protect the data new technique is used with striping called parity. This is a reliable and low-cost solution for data protection. In this method, an additional HDD or disk is added to the stripe width to hold the parity bit.

Parity is a redundancy check that ensures full protection of data without maintaining a full set of duplicate data.

 

RAID Parity

 

The parity bits are used to re-create the data at the time of failure. Parity information can be stored on separate, dedicated HDDs or distributed across all the drives in a RAID set. In the above image, parity is stored on a separate disk.

 

Recommended Article: RAID 5 vs RAID 6

 

The first three disks, labeled D, contain the data. The fourth disk, labeled P, stores the parity information, which in this case is the sum of the elements in each row. Now, if one of the Disks (D) fails, the missing value can be calculated by subtracting the sum of the rest of the elements from the parity value.

Hope you have understood the basic of these RAID levels. If you have any issues or concerns, please let us know through your emails and comment.

Buy me a coffeeBuy me a coffee

32 Comments

  1. Pingback: Create Partition for RAID in Linux/Unix April 8, 2013
  2. Qamber April 29, 2015
  3. Hussain June 6, 2015
    • ST June 6, 2015
  4. TAU August 14, 2015
    • ST August 15, 2015
      • Sudip Chatterjee April 24, 2017
  5. sudip chatterjee August 19, 2015
    • ST September 2, 2015
      • Sudip Chatterjee May 13, 2017
  6. raghuraman December 7, 2015
    • ST December 8, 2015
  7. Selim Mohammad May 18, 2016
  8. Neeraj bhatt May 20, 2016
  9. noura October 22, 2016
    • ST October 24, 2016
  10. Akshay kasar February 19, 2017
    • ST February 21, 2017
  11. Manohar February 21, 2017
    • ST February 21, 2017
  12. Venky April 9, 2017
    • ST April 9, 2017
  13. kk May 31, 2017
    • ST June 2, 2017
  14. Sanjay jarha June 14, 2017
    • ST June 18, 2017
  15. udhay May 12, 2018
    • ST May 12, 2018
  16. KLB8 February 18, 2021
  17. Devanshi April 24, 2021
  18. Sumeet S. Yogi June 13, 2021

Leave a Reply to ST Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.